Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
May 29, 2023
My washing machine seams to be getting louder when it’s in the spin cycle , doesn’t sound like grinding or thumping noises ? No squeaking noises . The washer is pretty quit until it goes into the spin cycle ? Machine is in my basem*nt and I can hear it spinning from my first floor ? I haven’t dug into anything? No leaking , washes clothes fine just getting louder ?
For model number MVWC425BW0
Hi Mike, thank you for reaching out. Based on the description that you have provided, we would recommend checking the drive belt, part number PS11747978, to fix this issue. We hope this solves your issue!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Drive Belt
$27.47
In Stock
Mike
June 7, 2023
My washing machine seams to be getting louder , I replaced the belt and that didn’t do anything it’s mainly noisy during the spin cycle ? But you can spin the drum by hand with no load in it and it seams loud ? It doesn’t leak or squeal ,seams to do the wash okay ? I can hear it spin from the basem*nt when I’m on the first floor ? Is there a bearing or something that goes ? Hard to explain what it sounds like ? Not really a grinding noise? It’s like when you’re driving your car and you go from asphalt (quite)to concrete ( noisier road noise ) the way you get that different sound ?
For model number MVWC425BW0
Hello Mike, thank you for reaching out. Based on our understanding of the issue, we would suggest you replace the washer gearcase, part number PS16220910, to fix the issue. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Sandy
March 3, 2020
First my washer would not stop. It would get to end of cycle and start over with out unlocking. Yesterday I tried washing a load and it will not spin or unlock the door.
For model number MVWC425BW0
Hello Sandy, Thank you for the question. This could be a defective Lid Latch Assembly, PartSelect Number PS3497627. You could try testing the part with a multimeter to see if it has electrical continuity, and if it does not show continuity, replace it. I hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
Lid Latch Assembly
$72.93
In Stock
Bonnie
July 13, 2021
When I press the start button to start a cycle, it locks, then immediately unlocks and the Green sensing light flashes
For model number MVWC425BW0
Hello Bonnie, Thank you for the question. When a washer sensing light is blinking, this is usually an indication the the motor cannot engage. This could be because the lid is not properly closed or locked. The Lid Latch Assembly might be defective and needs to be replaced. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Lid Latch Assembly
$72.93
In Stock
Gregory
February 26, 2023
Washer is making a ratcheting noise while agitating .This has just started a couple of days ago
For model number MVWC425BW0
Hi Gregory, thank you for reaching out. According to our research, the most common causes of a washer making a loud noise during the agitation cycle are the worn-out drum suspension rod assembly, part number PS11703287, the broken drive pulley, part number PS10057144, and a faulty drive belt, part number PS11747978. If that does not help, we would recommend checking the gearcase, part number PS16220910. Good luck with this repair!
Was this helpful?
Thank you for voting!
Related Parts:
Washer Drive Pulley
$69.35
In Stock
Washer Suspension Rod Kit
$152.93
In Stock
Drive Belt
$27.47
In Stock
Washer Gear Case
$430.91
In Stock
- < Prev
- 1
- 2
- Next >
Lid Lock light blinking, machine will not start
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
Parts Used:
-
David from Los Alamos, NM
-
Difficulty Level:
A Bit Difficult
-
Total Repair Time:
30 - 60 mins
-
Tools:
Nutdriver, Screw drivers
312 of 389 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Defective lid latch - Cabrio Washer
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Parts Used:
-
William from Wakefield, RI
-
Difficulty Level:
Very Easy
-
Total Repair Time:
15 - 30 mins
-
Tools:
Nutdriver, Screw drivers
93 of 112 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Parts Used:
-
Jerry from WALLA WALLA, WA
-
Difficulty Level:
Really Easy
-
Total Repair Time:
15 - 30 mins
-
Tools:
Nutdriver, Screw drivers, Socket set
84 of 114 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
